Fluke 2062

Main features

Quickly and accurately locate live and dead wires in walls, ceilings and floors.
The patented Smart Sensor™ technology locates and displays live wires on the colour screen.
Locate breaks, open circuits and short circuits and easily identify switches and fuses.
Safety category CAT IV 600 V.
Includes the AC clamp meter i400, which allows inducing a locating signal on the cable when access to bare conductors is not possible.

Check the lead time with Edimar.

Available on backorder

2.585,00 € excluding VAT - 3.127,85 € including VAT

Available on backorder

✓ This product supports 3% welcome discount. Conditions

EAN: 00195112044575 SKU 5353866 Categories Electronic Instrumentation, Cable locator Brand: Fluke

MPN: 5353866

Share this product:

Description

Specifications: Fluke 2062 Pro advanced cable locator kit

General

	Receiver 2062R	Transmitter 2000T	AC clamp meter i400
Safety category	CAT IV 600 V	CAT IV 600 V	CAT IV 600 V, CAT III 1000 V
Operating voltage	600 V CA/CC	600 V CA/CC	1000 V CA
Operating frequency	With voltage: 6,25 kHz Without voltage: 32,768 kHz	With voltage/loop: 6,25 kHz Without voltage: 32,768 kHz	N/A
Signal indications	Numeric display, bar graph and audible beep	LED and audible beep	N/A
Response time	Smart Sensor: 500 ms Tip sensor (with/without voltage): 500 ms NCV: 500 ms Battery monitoring: 5 s	Line voltage monitoring: 1 s Battery voltage monitoring: 5 s	N/A
Output signal current (typical)	N/A	Circuit with voltage: High mode: 60 mA rms Low mode: 30 mA rms Circuit without voltage: High mode: 110 mA rms Low mode: 40 mA rms Loop mode with test leads: 160 mA rms Loop mode with AC clamp meter i400: 385 mA rms	N/A
Output signal voltage (nominal)	N/A	Circuit with voltage: High mode: 14 W at 230 V CA/50 Hz, 3,33 kΩ at 230 VAC Low mode: 4,6 W at 230 V CA/50 Hz, 11,5 kΩ at 230 VAC Circuit without voltage: High mode: 31 V RMS, 140 Vp-p, 0,86 W at 1 kΩ load Low mode: 27,5 V RMS, 120 Vp-p, 0,1 W at 1 kΩ load Loop mode with test leads: 32 V RMS, 140 Vp-p, 0,87 W at 1 kΩ load Loop mode with AC clamp meter i400: 31 mV, 0,89 W at 1 Ω load	N/A
Detection distance (open air)	Smart Sensor direction indication mode ≤15 cm (6”), 230 VAC, high mode, sensitivity level 2 Tip sensor: With voltage Maximum open air distance: up to 6,1 m (20 feet) Localización exacta: aprox. 5 cm (1,97″) Tip sensor: Without voltage Maximum open air distance: up to 4,5 m (14,7 feet) Localización exacta: aprox. 5 cm (1,97″) NCV (40 Hz to 400 Hz): Maximum sensitivity: 90 V up to 2 m Minimum sensitivity: 600 V up to 1 cm	N/A	N/A
Current range	N/A	N/A	400 A
Basic accuracy	N/A	N/A	2% + 0,06 A (45 Hz to 400 Hz)

Display

	Receiver 2062R	Transmitter 2000T	AC clamp meter i400
Display size	LCD 3,5″ (89 mm)	LED	N/A
Display dimensions (width x height)	70 x 52 mm (2,76 x 2,07″)	N/A	N/A
Display resolution	480 pixels x 320 pixels	N/A	N/A
Display type	Colour TFT LCD	LED	N/A
Display colour	16 bits	Operating mode LED: red Battery status LED: green, yellow, red	N/A
Backlight	Yes	N/A	N/A

Environmental

	Receiver 2062R	Transmitter 2000T	AC clamp meter i400
Operating temperature	−20 °C to 50 °C (−4 °F to 122 °F)	−20 °C to 50 °C (−4 °F to 122 °F)	−20 °C to 50 °C (−4 °F to 122 °F)
Operating humidity	45%: -20 °C to <10 °C or 40 °C to 50 °C (-4 °F to <50 °F or 104 °F to 122 °F) 95% (non-condensing): 10 °C to <30 °C (50 °F to 86 °F) 75%: 30 °C to <40 °C (86 °F to <104 °F)	45%: -20 °C to <10 °C or 40 °C to 50 °C (-4 °F to <50 °F or 104 °F to 122 °F) 95% (non-condensing): 10 °C to <30 °C (50 °F to 86 °F) 75%: 30 °C to <40 °C (86 °F to <104 °F)	10 °C to <30 °C (95 %: from 50 °F to <86 °F) From 30 °C to <40 °C (75 %: from 86 °F to <104 °F) From 40 °C to <50 °C (45 %: from 104 °F to <122 °F)
Operating altitude	2000 m (6561 feet)	2000 m (6561 feet)	2000 m (6561 feet)
Transient protection	N/A	8,00 kV (peaks of 1,2/50 μs)	N/A
Pollution degree	2	2	2
IP protection	IP 40	IP 40	IP 40
Drop test	1 m (3,28 feet)	1 m (3,28 feet)	1 m (3,28 feet)

Mechanical

	Receiver 2062R	Transmitter 2000T	AC clamp meter i400
Power supply	4 AA batteries (alkaline)	8 AA batteries (alkaline)	N/A
Consumption (typical)	110 mA	High/low mode: 70 mA Loop mode with clamp: 90 mA Consumption without transmission signal: 10 mA	N/A
Battery life	Approx. 20 h	High/low mode: approx. 25 h Loop mode: approx. 18 h	N/A
Low charge indication	Yes	Yes	N/A
Fuse	N/A	1,6 A, 700 V, fast acting, Ø 6 x 32 mm, breaking capacity 50 kA	N/A
Maximum conductor size	N/A	N/A	32 mm (1,26″)
Dimensions (L x W x H)	Aprox. 277 x 112 x 65 mm (10,92 x 4,43 x 2,55″)	Aprox. 183 x 93 x 50 mm (7,2 x 3,66 x 1,97″)	Aprox. 150 x 70 x 30 mm (5,9 x 2,75 x 1,18″)
Weight	Approx. 0,544 kg (1,20 lb)	Approx. 0,57 kg (1,25 lb)	Approx. 0,114 kg (0,25 lb)

Accessory and test cable kit 2000ACC

Includes:
- 2 test cables of 1 m (red, black)
- 1 test cable of 7 m (green)
- 2 test probes (black)
- 2 crocodile clips (red and black)
- 2 flat socket adapters (red, black)
- 2 round socket adapters (red, black)
Safety category: CAT IV 600 V (test cables), CAT II 1000 V (test probes), CAT IV 600 V (crocodile clips), CAT II 300 V (socket adapters)
Operating voltage and current: 600 V, 10 A max. (red and black cables), 600 V, 10 A max. (green cable), 1000 V, 8 A max. (test probe)
Water and dust protection: IP 20
Drop resistance: 1 m (3,28 feet)

Downloads